العربية

العربية

Get a Quote
منتجات

منتوجات جديدة

أخبار الشركة

How to Install the Valve Gasket?
How to Install the Valve Gasket?
2023-06-07

Sealing gasket is a commonly used sealing spare part for machinery, equipment, etc. It is a material that plays a sealing role. Correct installation can ensure sealing performance and smooth operation of the equipment, otherwise it will damage the sealing gasket. Next, let's take a specific look at what to do. The correct installation of gaskets should be carried out when the flange connection structure or threaded connection structure, sealing surface, and gasket have been inspected without any doubt, and other valve components are intact and undamaged. 1. Before installing the gasket, apply a layer of graphite powder or lubricant mixed with engine oil (or water) to the sealing surface, gasket, thread, and rotating parts of the bolt and nut. The gasket and graphite should be kept clean. 2. The gasket should be installed on the sealing surface in a moderate and correct manner, without deviation, and should not extend into the valve chamber or rest on the shoulder. 3. Only one gasket is allowed to be installed, and it is not allowed to install two or more gaskets between the sealing surfaces to eliminate insufficient clearance between the two sealing surfaces. 4. The sealing of elliptical gaskets should ensure that the inner and outer rings of the gasket come into contact, and the two ends of the gasket should not come into contact with the bottom of the groove. 5. The installation of the O-ring should not only meet the design requirements for the ring and groove, but also have an appropriate amount of compression. On the premise of ensuring sealing, the smaller the compression deformation rate, the better, which can extend the service life of the O-ring. 6. Before installing the gasket, the valve should be in the open position to avoid affecting installation and damaging the valve components. When covering, it should be aligned with the position and should not be pushed or pulled into contact with the gasket to avoid displacement and scratches on the gasket. 7. The installation of gaskets for bolted or threaded connections should ensure that the gaskets are in a horizontal position (threaded gaskets with wrench positions should not be used with pipe wrenches). 8. Before tightening the gasket, it is necessary to have a clear understanding of the pressure, temperature, properties of the medium, and material characteristics of the gasket to determine the pre tightening force. The preload should be minimized as much as possible without leakage during pressure testing. 9. After tightening the gasket, it is necessary to ensure that there is a pre tightening gap between the connecting parts in case of gasket leakage. 10. When working at high temperatures, bolts will experience high-temperature creep, stress relaxation, and increased deformation, leading to leakage at the gasket and requiring hot tightening. On the contrary, under low temperature conditions, bolts will shrink and require cold loosening. 11. When liquid sealing gaskets are used for sealin...

ما هو الفرق بين صمام البوابة وصمام الكرة الأرضية؟
ما هو الفرق بين صمام البوابة وصمام الكرة الأرضية؟
2023-05-31

يعتقد الكثير من الناس أن كلاً من صمامات البوابة وصمامات الكرة الأرضية لها وظيفة قطع الوسائط ، لذلك لا تختلف عند استخدامها. في الواقع ، هناك اختلافات معينة بين صمامات البوابة وصمامات الكرة الأرضية في التطبيقات العملية. Gate Valve and Structural Diagram Globe Valve and Structural Diagram 1. Having different structures. Gate valves are more complex in structure, higher in height, and larger in size than globe valves. Gate valves are shorter and higher in appearance than globe valves. Especially, opening the stem gate valve requires a higher height. If the installation position of the valve is limited, it is necessary to choose rising stem and non-rising stem gate valves and remind everyone to pay attention. 2. When fully open, it has different flow resistance. The flow resistance coefficient of ordinary gate valves is approximately 0.08~0.12. The pressure loss during the operation of the gate valve medium is small, and the fluid flow resistance is small. Gate valves are usually suitable for working conditions where frequent opening and closing are not required and the gate is kept fully open or closed. It is not suitable for adjustment and throttling. The resistance coefficient of a regular globe valve is about 3.5-4.5, and the opening and closing forces are very small. The flow resistance of the shut-off valve throughout its entire stroke is very high, and the required driving force or torque is also much greater. But it is very suitable for regulation and throttling. 3. The flow direction of the medium inside the valve body is different. Gate valves have the same effect when viewed from both sides. When installing a shut-off valve, the medium can enter from below and above the valve core. 4. The sealing surface of the gate valve has a certain degree of self-sealing ability. The valve core is in close contact with the sealing surface of the valve seat through medium pressure, achieving sealing performance and no leakage. The sealing surfaces of the shut-off valve only come into contact with each other when fully closed, and the relative sliding amount between the forcibly closed valve core and the sealing surface is very small, so the wear of the sealing surface is also very small. 5. The maintenance procedures are different. The maintenance of gate valves is not applicable to on-site pipelines, but the seat and disc of most globe valves can be replaced online without the need to remove the entire valve from the pipeline (when the valve is not under pressure). This is very suitable for situations where valves and pipelines are welded together. Gate and globe valves are both fully open and fully closed valves. When selecting valves in the application process, attention should be paid to the characteristics of the valves. Globe valves are usually used for small pipelines and

تكنولوجيا المعالجة والخصائص الهيكلية لصمام الفراشة ذو الختم الصلب الثلاثي غريب الأطوار
تكنولوجيا المعالجة والخصائص الهيكلية لصمام الفراشة ذو الختم الصلب الثلاثي غريب الأطوار
2023-05-24

صمام الفراشة ذو الختم الصلب الثلاثي اللامركزي ، كصمام عالي الأداء ، له مزايا مثل مقاومة التآكل ، الختم الموثوق به ، وعزم الدوران الصغير للفتح. سطحه المحكم هو سطح مخروطي مائل ، والاتصال بين حلقة إحكام إغلاق جسم الصمام وحلقة إحكام تجميع لوحة الفراشة هي ملامسة السطح. مبدأ عملها هو قيادة مجموعة لوحة الفراشة مباشرة عن طريق عزم دوران جهاز القيادة ، مما يتسبب في اتصال حلقة الختم الخاصة بمجموعة لوحة الفراشة بشكل كامل بحلقة إحكام إغلاق جسم الصمام وتوليد تشوه مرن للختم. الخصائص الهيكلية 1. The hard sealed butterfly valve adopts a three eccentric hard sealing structure, with almost no wear on the valve seat and butterfly plate, and has a sealing function that becomes tighter as the valve is closed. 2. The sealing ring is made of stainless steel, which has the dual advantages of metal hard sealing and elastic sealing. Both at low and high temperatures, it has excellent sealing performance, corrosion resistance, and long service life. 3. The sealing surface of the butterfly plate adopts surfacing cobalt based hard alloy, which is wear-resistant and has a long service life. 4. The large-sized butterfly plate adopts a quilted frame structure, with high strength, large flow area, and small flow resistance. 5. According to user requirements, hard sealed butterfly valves can be designed with bidirectional sealing function. During installation, it is not limited by the flow direction of the medium or affected by spatial location, and can be installed in any direction. 6. The drive device can be installed in multiple workstations (rotating 90 ° or 180 °), making it easy for users to use. Processing Technology Based on the structural characteristics of the triple eccentric metal hard seal butterfly valve, the sealing ring of the butterfly plate assembly is a combination of stainless steel plate, asbestos plate, or graphite. The valve body sealing ring is made of hard alloy with high hardness, and it is difficult to control the cutting amount, making it difficult to process and shape in one go. Moreover, the roughness requirements for the machined surface are very high. To ensure processing requirements, the process is as follows: Rough machining of valve body or butterfly plate assembly →→ Valve body sealing ring is welded with hard alloy for insulation and heat treatment to eliminate thermal stress →→ Sealing surface of rough turning of upper tooling →→ Upper tooling precision turning sealing surface →→ Grinding sealing surface with upper grinding head →→ Boring shaft holes for valve body and butterfly plate assembly →→ Strength test sealing test

خمسة آلاف ومائتان واحد
加载中...

4 بوصة 150 رطل العروة صمام فراشة متحدة المركز حديد الدكتايل

هذا الفراشة المتركزة الصمام هو صمام من النوع ذي الفتحات الملولبة ويمكن استخدامه للعديد من التطبيقات. ال يمكن استخدام الصمام كسدادة ، وحنفية للتفريغ في نهاية خط الأنابيب ، فتح / إغلاق والتحكم في التدفق

  • دفع:

    30% when order confirmed, 70% before shipment
  • أصل المنتج:

    China
  • اللون:

    Customization
  • ميناء الشحن:

    Shanghai, China
  • المهلة:

    30~60 days Ex Works after order confirmation
  • Material:

    Ductile Iron
  • Method of Operation:

    Lever
الاستفسار الآن
تفاصيل المنتج

تفاصيل سريعة

اكتب

صمام فراشة

القطر الاسمي

4 بوصة

الضغط الاسمي

150 رطل

اعمال بناء

متحدة المركز النوع ؛ soft النوع ؛

الإتصال

مقبض النوع ؛

عملية

رافعة

تصميم & صناعة

API609

نهاية إلى نهاية البعد

EN558-1

اختبار & تفتيش

EN12266

مادة الجسم

الدكتايل الحديد

مادة القرص

الدكتايل الحديد

وسائل الإعلام

دبليو أو جي

المميزات

- مقاعد مرنة

متحدة المركز صمام الفراشة API609

-نوع -Lug مع ثقوب مترابطة

-إغلاق صمام مياه الشرب والخدمة حتى 120 درجة مئوية

-ل الانزلاق بين الشفاه الأنابيب

-As نهاية الصمام للضغط التفاضلي الكامل

- ضيق في كلا اتجاهي التدفق

-مضاد الانفجار مهاوي

رسم تقنى _ رسم عن طريق الكمبيوتر


فحص البعد


التعبئة


حول Dervos

شيامن Dervos شركة صناعة الصمامات المحدودة (الأسهم كود 861601) ، التي تأسست في يونيو 2008 ، هي مورد صمامات صناعية متكامل للبحث والتطوير والتصنيع وتكامل الموارد والتجارة الخدمة عن 12 عامًا ، Dervos ملتزمة بإيجاد حلول للاحتياجات الصناعية وتقديم خدمة احترافية لكل من الصمامات العامة والمتخصصة.



اترك رسالة

إذا كنت مهتما في منتجاتنا و تريد أن تعرف المزيد من التفاصيل,يرجى ترك رسالة هنا وسوف نقوم بالرد عليك بأسرع ما يمكن.

منتجات ذات صله
صمام فراشة متحد المركز من الحديد الزهر
يلقي الحديد رقاقة نوع متحدة المركز فراشة صمام pn10 dn200

يتكون صمام فراشة ذراع متحدة المركز من الحديد الزهر gg25 ، ss420 الجذعية ، ومقعد epdm. صمام فراشة dn200 قابل للتطبيق على الماء. تفاصيل سريعة نوع فراشة   صمام الحجم الاسمي dn200 الضغط الاسمي pn10 بناء متحدة المركز   اكتب ، epdm يجلس لينة نوع الاتصال رقاقة   نوع عملية رافعة   تعمل كود التصميم en   593 وجها لوجه en   558 نهاية الاتصال en   1092 اختبار & أمبير ؛   تفتيش en   12266 مواد الجسم المصبوب   الحديد gg25 نطاق درجة حرارة -15 ℃ ~ + 150 ℃ تطبيق ماء،   النفط والغاز التعديلات المتاحة لصمامات الفراشة -صمام ضغط اسمي -صمام الحجم الاسمي - نوع غريب الأطوار ونوع غريب الأطوار - مقعد ناعم ، مقعد معدني متعدد الطبقات ، مقعد معدني بالكامل -الهيئة & أمبير ؛ تقليم المواد اتصال نهاية (مزدوجة الشفاه ، رقاقة ، العروة) - التشغيل المتوفر (الساق العارية ، المحرك الكهربائي ، المحرك الهوائي ، الرافعة أو المفتاح) طلاء حسب الطلب تغليف حسب الطلب تطبيق المنتج زيت & أمبير ؛ صناعة الغاز تعمل صمامات dervos بشكل كامل في صناعات التكرير والنفط والغاز للتعامل مع بيئات العمل الصعبة للغاية. صناعة بتروكيماوية يمكننا أيضًا توفير جميع أنواع الصمامات في مواد مختلفة ، مثل الفولاذ المقاوم للصدأ ، مونيل ، تيتانيوم ، وهاستلوي لتلبية متطلبات الصناعة الكيميائية. صناعة محطات الطاقة يمكن أن توفر شركة Dervos صمامات مناسبة لاستخدام محطة الطاقة مع متطلبات الضغط العالي ودرجة الحرارة.

خمسة آلاف ومائتان واحد
يلقي الصلب نوع رقاقة فراشة صمام 2 بوصة 300 رطل رافعة

مزود صمام فراشة نوع رقاقة الصين DVS توريدات صمام فراشة من الصلب المصبوب ، 2 بوصة ، فئة 300 ، ذراع تشغيل للهواء والماء والبخار والغازات.

صمام فراشة
صمام فراشة متحدة المركز DN300 PN10 FF API609

تم تصنيع صمام الفراشة DN300 PN10 وفقًا لمعيار API 609. جسم الصمام مصنوع من GGG40. لها الخصائص الهيكلية للخط المركزي والطول الهيكلي 78 مم. وضع الاتصال الخاص به هو FF. ولها وضع تشغيل التوربينات.

صمام فراشة
10 "150LB فراشة صمام العروة GGG40 API609 رافعة

تم تصنيع صمام الفراشة 10 "150LB وفقًا لمعيار API 609. جسم الصمام مصنوع من GGG40. له الخصائص الهيكلية لنوع الخط المتوسط ​​ونوع العروة (الفتحة الملولبة). وضع الاتصال الخاص به هو العروة. وله وضع تشغيل الرافعة .

خمسة آلاف ومائتان واحد
2 قطعة صمام الكرة العائمة wcb 150lb 4 inch تتحمل تجويف

يحتوي الصمام الكروي العائم المكون من قطعتين ، والمصنوع وفقًا لـ api 6a ، على تصميم منخفض التجويف ، وتصميم آمن للحريق ، وجذع مانع للانفجار. مع مقعد rptfe وخاتم ptfe o ، فإن صمام wcb 4 بوصة هو شهادة لخدمتك.

خمسة آلاف ومائتان واحد
3 قطعة موقف نوع الكرة صمام، ASTM A105N، فئة 800، 1 بوصة

الصين كربون الصلب الكرة صمام مزود عروض 3 قطعة صمام الكرة نوع موقف، ASTM A105N، فئة 800، 1 بوصة، كرة عائمة مجانية، API 608، بكالوريوس 5351.

خمسة آلاف ومائتان واحد
مشغل تروس صمام كروي مكون من 3 قطع A105 4 بوصة 150 رطل

ال 4 بوصة 150 رطل صمام الكرة هو 3 قطع واحد مع منفذ مخفض ، A105 الجسم ، F6A جذع وكرة و مقعد. ال ال تم تصنيع الصمام حسب لكل API6D ويتم اختباره بموجب API 598.

صمام مونيل غلوب
3 "Class300 Monel Globe Valve RF HF عجلة اليد الحمضية

تم تصنيع صمام الكرة الأرضية فئة 300 3 بوصات وفقًا لمعيار BS1873 ، وجسم الصمام مصنوع من مادة Monel ، ووضع الاتصال هو RF ، ولديه وضع تشغيل عجلة اليد.

قطعتين صمام الكرة الصلب
الصب 2 قطعة الكرة صمام 4 بوصة فئة 150 وجع

نوع قطعة 2 صمام الكرة العائمة لديه منفذ كامل ، تصميم آمن من الحرائق ، جذع مضاد للانفجار ، شفة ansi 150 وعملية رافعة. تم تصميم صمام الكرة الكربونية الفولاذية مع جسم a1616 wcb ، f316 الساق والكرة ، مقعد ناعم ptfe. تفاصيل سريعة نوع صمام الكرة بحجم 4 " الضغط 150 رطل اعمال بناء نوع عائم   كرة ، قطعتين من الجسم ، تتحمل كامل الإتصال رفع   شفة الوجه عملية مفتاح الربط   عملية الجسم   مواد فولاذ صلب   WCB تقليم   مواد SS316 & أمبير ؛ ptfe معيار التصميم واجهة برمجة التطبيقات 6 د الضغط   & أمبير ؛ كود مؤقت اسمي ب 16.34 وجها لوجه Asme b16.10 النهاية   الإتصال Asme b16.5 تفتيش   الشفرة واجهة برمجة التطبيقات 6 د درجة الحرارة   نطاق -29 ℃ ~ + 125 ℃ وسائل الإعلام الماء والنفط   والغاز المواد و أمبير ؛ البعد لا جزء اسم كربون   الصلب ل astm غير القابل للصدأ   الصلب ل astm WCB lcb راجع 8 CF 8M راجع 3 CF3M 1 الجسم a216 wcb a352 lcb a351 cf8 a351 cf8m a351 cf3 a351 cf3m 2 بونيه الجوز أ 194 2 ساعة أ 194 4 أ 194 8 3 بونيه الترباس أ 193 ب 7 A320 l7 أ 193 ب 8 4 قبعة a216 wcb a352 lcb a351 cf8 a351 cf8m a351 cf3 a351 cf3m 5 طوقا ss دوامة الجرح / الجرافيت أو   ss الجرح اللولبي / ptfe 6 كرة a105 / ep.cr أو f6 a182 f6 a351 cf8 a351 cf8m a351 cf3 a351 cf3m 7 حلقة مقعد rptfe أو بوم 8 ربيع صغير الفولاذ المقاوم للصدأ 9 كرة صغيرة a182 f304 a182 f316l 10 إيقاف a182 f6 a182 f6 a182 f304 a182 f316 a182 f304l a182 f316l 11 مقعد الجذعية السليكوون 12 التعبئة الجذعية السليكوون أو الجرافيت 13 السدادة a182 f6 a182 f304 a182 f316 a182 f304l a182 f316l 14 الترباس الغدة أ 193 ب 7 أ 193 ب 8 15 شفة galnd a216 wcb a351 cf8 16 لوحة تحديد المواقع صلب 17 صنم a216 wcb كانت المادة   وفقًا لمعيار ASTM الفئة 150 د مم 15 20 25 40 50 65 80 100 150 200 250 NPS في 0.5 0.75 1 1.5 2 2.5 3 4 6 8 10 ل (الترددات اللاسلكية) مم 108 117 127 165 178 191 203 229 394 457 533 في 4.25 4.6 5 6.5 7 7.5 8 9 15.5 18 21 ل 1 (وزن الجسم) مم 140 152 165 190 216 241 283 305 457 521 559 في 5.5 6 6.5 7.48 8.5 9.5 11.13 12 18 20.5 22 ل 2 (رتج) مم 119 129.7 139.7 178 191 203 216 241 406 470 546 في 4.69 5.11 5.5 6.9 7.5 8 8.5 9.5 16 18.5 21.5 ح مم 66 74 87 105 132 152 182 215 250 285 495 في 2.6 2.9 3.48 4.2 5.28 6.08 7.28 8.6 10 11.4 19.5 افعل (ث) مم 130 130 160 230 400 400 600 850 1100 1500 * 350 في 5.1 5.11 6.3 9 15.74 15.74 23.62 33.46 43.3 59 13.8 الترددات اللاسلكية (كلغ) & emsp؛ 2.3 3 4.5 7 15 20 25 40 97 160 240 وزن الجسم (كجم) & emsp؛ 2.0 2.5 3.8 5.8 12 17 21 36 92.8 154 227 * تعمل معدات دودة أو المحرك الكهربائي اختبارات خاصة & أمبير ؛ عمليات التفتيش بالإضافة إلى الاختبار الهيدروليكي المنتظم واختبار الهواء ، يمكن لـ Dervos أيضًا إجراء اختبارات خاصة وفقًا لطلبات العملاء ، مثل اختبار pt ، اختبار rt ، اختبار ut ، اختبار المبردة ، اختبار التسرب المنخفض ، اختبار مقاومة الحرائق ، واختبار الصلابة وما إلى ذلك .

صمام الكرة العائمة
1 بوصة 800LB العائمة الكرة صمام الفولاذ المقاوم للصدأ SW

تقوم Dervos بتصنيع مجموعة متنوعة من الصمامات الكروية في تركيبات مفردة وثنائية وثلاثية القطع. تتوفر الصمامات في تصميمات التجويف الكامل والمنتظم ، في مجموعة متنوعة من الوصلات الطرفية والمواد لتلبية متطلباتك.

 صمام فراشة غريب الأطوار ثلاثي
الكربون الصلب الثلاثي فراشة صمام غريب الأطوار 150lb 20 بوصة

تم تصميم صمام الفراشة غريب الأطوار الثلاثي ، المصنوع من الفولاذ الكربوني ، تحت الفئة 150 للحصول على أداء أفضل للتسرب. مع مشغل التروس ، يمكن أن يكون أفضل. تفاصيل سريعة نوع صمام فراشة الحجم الاسمي 20 بوصة الضغط الاسمي الفئة 150 بناء تعويض ثلاثي ، غريب الأطوار ثلاثي ، يجلس معدن نوع الاتصال نوع الرقاقة عملية تعمل معدات كود التصميم api 609 وجها لوجه Asme b16.10 نهاية الاتصال Asme 16.5 اختبار & أمبير ؛ تفتيش api 598 مواد الجسم الكربون الصلب تطبيق الماء والنفط والغاز تأسست في عام 2008 ، شركة dervos valves industry. ltd هي بائع محترف ومصدر ومورد للصمامات الصناعية والأنابيب والتجهيزات. قامت شركة Dervos بتوسيع أعمالها إلى خمس قارات حول العالم ، بما في ذلك أوروبا وأوقيانوسيا وأفريقيا وأمريكا وآسيا. التزامنا هو العثور على أنسب المنتجات لعملائنا بطريقة فعالة. نعتمد المهارات الإدارية الحديثة للتأكد من الكفاءة في نظام الإنتاج والبيع.

صمام بوابة برونزي
1 بوصة 800LB البرونزية بوابة صمام API602

يختلف من 1/4 بوصة إلى 3 بوصة ، صمام البوابة هذا مصنوع من البرونز B62 وفقًا لـ API602. بغض النظر عن تصنيف الضغط أو تصميم الخيط أو الحجم الذي تحتاجه ، فإن Dervos لديها مجموعة كبيرة من الصمامات لتلبية احتياجاتك.

اترك رسالة

    إذا كنت مهتما في منتجاتنا و تريد أن تعرف المزيد من التفاصيل,يرجى ترك رسالة هنا وسوف نقوم بالرد عليك بأسرع ما يمكن.

الصفحة الرئيسية

منتجات

حول

اتصل