العربية

العربية

Get a Quote
منتجات

منتوجات جديدة

أخبار الشركة

How to Install the Valve Gasket?
How to Install the Valve Gasket?
2023-06-07

Sealing gasket is a commonly used sealing spare part for machinery, equipment, etc. It is a material that plays a sealing role. Correct installation can ensure sealing performance and smooth operation of the equipment, otherwise it will damage the sealing gasket. Next, let's take a specific look at what to do. The correct installation of gaskets should be carried out when the flange connection structure or threaded connection structure, sealing surface, and gasket have been inspected without any doubt, and other valve components are intact and undamaged. 1. Before installing the gasket, apply a layer of graphite powder or lubricant mixed with engine oil (or water) to the sealing surface, gasket, thread, and rotating parts of the bolt and nut. The gasket and graphite should be kept clean. 2. The gasket should be installed on the sealing surface in a moderate and correct manner, without deviation, and should not extend into the valve chamber or rest on the shoulder. 3. Only one gasket is allowed to be installed, and it is not allowed to install two or more gaskets between the sealing surfaces to eliminate insufficient clearance between the two sealing surfaces. 4. The sealing of elliptical gaskets should ensure that the inner and outer rings of the gasket come into contact, and the two ends of the gasket should not come into contact with the bottom of the groove. 5. The installation of the O-ring should not only meet the design requirements for the ring and groove, but also have an appropriate amount of compression. On the premise of ensuring sealing, the smaller the compression deformation rate, the better, which can extend the service life of the O-ring. 6. Before installing the gasket, the valve should be in the open position to avoid affecting installation and damaging the valve components. When covering, it should be aligned with the position and should not be pushed or pulled into contact with the gasket to avoid displacement and scratches on the gasket. 7. The installation of gaskets for bolted or threaded connections should ensure that the gaskets are in a horizontal position (threaded gaskets with wrench positions should not be used with pipe wrenches). 8. Before tightening the gasket, it is necessary to have a clear understanding of the pressure, temperature, properties of the medium, and material characteristics of the gasket to determine the pre tightening force. The preload should be minimized as much as possible without leakage during pressure testing. 9. After tightening the gasket, it is necessary to ensure that there is a pre tightening gap between the connecting parts in case of gasket leakage. 10. When working at high temperatures, bolts will experience high-temperature creep, stress relaxation, and increased deformation, leading to leakage at the gasket and requiring hot tightening. On the contrary, under low temperature conditions, bolts will shrink and require cold loosening. 11. When liquid sealing gaskets are used for sealin...

ما هو الفرق بين صمام البوابة وصمام الكرة الأرضية؟
ما هو الفرق بين صمام البوابة وصمام الكرة الأرضية؟
2023-05-31

يعتقد الكثير من الناس أن كلاً من صمامات البوابة وصمامات الكرة الأرضية لها وظيفة قطع الوسائط ، لذلك لا تختلف عند استخدامها. في الواقع ، هناك اختلافات معينة بين صمامات البوابة وصمامات الكرة الأرضية في التطبيقات العملية. Gate Valve and Structural Diagram Globe Valve and Structural Diagram 1. Having different structures. Gate valves are more complex in structure, higher in height, and larger in size than globe valves. Gate valves are shorter and higher in appearance than globe valves. Especially, opening the stem gate valve requires a higher height. If the installation position of the valve is limited, it is necessary to choose rising stem and non-rising stem gate valves and remind everyone to pay attention. 2. When fully open, it has different flow resistance. The flow resistance coefficient of ordinary gate valves is approximately 0.08~0.12. The pressure loss during the operation of the gate valve medium is small, and the fluid flow resistance is small. Gate valves are usually suitable for working conditions where frequent opening and closing are not required and the gate is kept fully open or closed. It is not suitable for adjustment and throttling. The resistance coefficient of a regular globe valve is about 3.5-4.5, and the opening and closing forces are very small. The flow resistance of the shut-off valve throughout its entire stroke is very high, and the required driving force or torque is also much greater. But it is very suitable for regulation and throttling. 3. The flow direction of the medium inside the valve body is different. Gate valves have the same effect when viewed from both sides. When installing a shut-off valve, the medium can enter from below and above the valve core. 4. The sealing surface of the gate valve has a certain degree of self-sealing ability. The valve core is in close contact with the sealing surface of the valve seat through medium pressure, achieving sealing performance and no leakage. The sealing surfaces of the shut-off valve only come into contact with each other when fully closed, and the relative sliding amount between the forcibly closed valve core and the sealing surface is very small, so the wear of the sealing surface is also very small. 5. The maintenance procedures are different. The maintenance of gate valves is not applicable to on-site pipelines, but the seat and disc of most globe valves can be replaced online without the need to remove the entire valve from the pipeline (when the valve is not under pressure). This is very suitable for situations where valves and pipelines are welded together. Gate and globe valves are both fully open and fully closed valves. When selecting valves in the application process, attention should be paid to the characteristics of the valves. Globe valves are usually used for small pipelines and

تكنولوجيا المعالجة والخصائص الهيكلية لصمام الفراشة ذو الختم الصلب الثلاثي غريب الأطوار
تكنولوجيا المعالجة والخصائص الهيكلية لصمام الفراشة ذو الختم الصلب الثلاثي غريب الأطوار
2023-05-24

صمام الفراشة ذو الختم الصلب الثلاثي اللامركزي ، كصمام عالي الأداء ، له مزايا مثل مقاومة التآكل ، الختم الموثوق به ، وعزم الدوران الصغير للفتح. سطحه المحكم هو سطح مخروطي مائل ، والاتصال بين حلقة إحكام إغلاق جسم الصمام وحلقة إحكام تجميع لوحة الفراشة هي ملامسة السطح. مبدأ عملها هو قيادة مجموعة لوحة الفراشة مباشرة عن طريق عزم دوران جهاز القيادة ، مما يتسبب في اتصال حلقة الختم الخاصة بمجموعة لوحة الفراشة بشكل كامل بحلقة إحكام إغلاق جسم الصمام وتوليد تشوه مرن للختم. الخصائص الهيكلية 1. The hard sealed butterfly valve adopts a three eccentric hard sealing structure, with almost no wear on the valve seat and butterfly plate, and has a sealing function that becomes tighter as the valve is closed. 2. The sealing ring is made of stainless steel, which has the dual advantages of metal hard sealing and elastic sealing. Both at low and high temperatures, it has excellent sealing performance, corrosion resistance, and long service life. 3. The sealing surface of the butterfly plate adopts surfacing cobalt based hard alloy, which is wear-resistant and has a long service life. 4. The large-sized butterfly plate adopts a quilted frame structure, with high strength, large flow area, and small flow resistance. 5. According to user requirements, hard sealed butterfly valves can be designed with bidirectional sealing function. During installation, it is not limited by the flow direction of the medium or affected by spatial location, and can be installed in any direction. 6. The drive device can be installed in multiple workstations (rotating 90 ° or 180 °), making it easy for users to use. Processing Technology Based on the structural characteristics of the triple eccentric metal hard seal butterfly valve, the sealing ring of the butterfly plate assembly is a combination of stainless steel plate, asbestos plate, or graphite. The valve body sealing ring is made of hard alloy with high hardness, and it is difficult to control the cutting amount, making it difficult to process and shape in one go. Moreover, the roughness requirements for the machined surface are very high. To ensure processing requirements, the process is as follows: Rough machining of valve body or butterfly plate assembly →→ Valve body sealing ring is welded with hard alloy for insulation and heat treatment to eliminate thermal stress →→ Sealing surface of rough turning of upper tooling →→ Upper tooling precision turning sealing surface →→ Grinding sealing surface with upper grinding head →→ Boring shaft holes for valve body and butterfly plate assembly →→ Strength test sealing test

خمسة آلاف ومائتان واحد
加载中...

انخفاض صمام بوابة مخفضة، بونيه ملحومة، وتركيب

الصين الملحومة بوابة بوابة بوابة منتج مصنوع من نسيج بوابة الصلب مزورة تتحمل، A105N، 1 / 2-4 بوصة، 150-1500 LB، بونيه الملحومة، لا يتجزأ

  • دفع:

    30% when order confirmed, 70% before shipment
  • أصل المنتج:

    China
  • اللون:

    Customization
  • ميناء الشحن:

    Shanghai, China
  • المهلة:

    30~60 days Ex Works after order confirmation
  • Material:

    Forged Steel
  • Method of Operation:

    Handwheel
الاستفسار الآن
تفاصيل المنتج

المواصفات الرئيسية / الميزات

النوع: مخفض بوابة الصلب مزورة صمام.
المواد: A105N، الخ
صمام الحجم: 1 / 2 - 4 بوصة.
الضغط المطبق التقييم: فئة 150 رطل - 1500 LB. .
درجة الحرارة التقييم: يصل إلى 500 ℃.
صب النمط: تزوير.


الصلب مزورة بوابة صمام - المسمار الخارجي & نير، انسحب بونيه


معيار المواد:

أسماء جزء

مواد

الجسم

A105؛ LF2؛ F5؛ F22؛ F304؛ F304L؛ F304؛ F316L؛ F347؛ F321؛ F51؛ F55؛ inconel مونيل hastelloy؛ إلخ.

غطاء محرك السيارة

A105؛ LF2؛ F5؛ F22؛ F304؛ F304L؛ F304؛ F316L؛ F347؛ F321؛ F51؛ F55؛ inconel مونيل hastelloy؛ إلخ.

مقعد

ASTM . A276 410 + هدف

وتد

ASTM . A276 420

إيقاف

ASTM . A276 410

طوقا

304 + الجرافيت

عجلة اليد

ASTM . A197 .

التعبئة

الجرافيت

السدادة

ASTM . A276 410



اختبار الضغط ( 105 )

صف دراسي

شل (PSIG)

الخلفية (PSIG)

مقعد (PSIG)

ماء

ماء

هواء

ماء

150LB

450

325

90.

-

300LB

1125

825

-

600lb

2225

1650

-

800lb

2975

2175

-

900lb

3350

2450

-

1500lb

5575

4100

-


تصميم وتصنيع المطابقة إلى: API . 602، BS5352، ASME B16.34 / B16.5.
الهيكل الميزات:
★ نهاية اتصال: تمتلى النوع
★ المسمار الخارجي & نير، انسحب بون نت.
★ تقليل تتحمل.
★ ارتفاع الجذعية / غير ترتفع عقارب.



DVS . تطبيق المنتج

Dervos . يمكن استخدام الصمامات على نطاق واسع في أنواع الصناعات، مثل البتروكيماويات والخط الأنابيب والنفط & الغاز، البحري، معالجة المياه، صناعات محطة الطاقة وغيرها


اترك رسالة

إذا كنت مهتما في منتجاتنا و تريد أن تعرف المزيد من التفاصيل,يرجى ترك رسالة هنا وسوف نقوم بالرد عليك بأسرع ما يمكن.

منتجات ذات صله
بونيه مزورة
مزورة الصلب صمام بوابة a105 الخيوط 1 بوصة 2500 رطل

يتميز صمام البوابة المعدنية المزورة بالضغط العالي الذي يبلغ ارتفاعه 2500 رطل بفتحة إسفين صلبة ومنفذ مخفض وغطاء مثبت بمسامير وعجلة يدوية وجذع مرتفع وخيط أنثوي (fnpt). تتوافق الصمامات المطروقة مع api 602 و api 598. تفاصيل سريعة نوع بوابة   صمام بحجم 1 " الضغط صف دراسي   2500 اعمال بناء ب ،   ارتفاع الساق ، نظام التشغيل ، إسفين صلب الإتصال مسلك   الإتصال عملية عقارب   تعمل مواد الجسم أستم   أ 105 مواد تقليم 13cr + stl التصميم api 602 من النهاية إلى النهاية ASTM B16.10 الضغط & أمبير ؛ مؤقت أستم b16.34 نهاية الاتصال astm b1.20.1 نطاق درجة حرارة -29 ℃ ~ + 425 ℃ متوسط wog الأصل الصين حدود المنتجمواد الجسم: الكربون الصلب والفولاذ المقاوم للصدأ وسبائك الصلب والفولاذ في درجة حرارة منخفضةالقطر العادي: 1/2 "~ 4"اتصال النهاية: وزن الجسم ، sw ، شفة ، مترابطةنطاق الضغط: 150 رطل ~ 2500 رطل (pn16 ~ pn420)العملية: عقارب ، ساق عارية ، مع المحركاتدرجة حرارة العمل: -46 ℃ ~ + 425 ℃ كيف نتحكم في الجودة أثناء عملية التصنيع؟ فحص الصب: تحقق من المظهر وسماكة الجدار والكمية والحجم وتقرير المواد الأصلية وما إلى ذلك. الإشراف على الآلات:الإشراف على عملية الإنتاج والعثور على المشاكل المحتملة لتجنب الإنتاج الخاطئ أو تصميم الإنتاج الخاطئ عن طريق زيارة المصنع بشكل عشوائي والتحقق من عملية التصنيع.

صمام بوابة api602
صمام بوابة api602 1 بوصة 0.75 بوصة 900 رطل من وزن الجسم عقارب وزن الجسم

api602 بوابة صمام الترباس بونيه خارج المسمار نير إسفين الصلبة خفض تتحمل تتحمل اتصال بعقب اللحام sch80s a182 f11 تقليم الجسم # 5 (13٪ cr + stl) 900 رطل 1 بوصة 3/4 بوصة تفاصيل سريعة نوع صمام البوابة بحجم 3/4 بوصة -1 بوصة ضغط التصميم cl900 اعمال بناء ب ، السراج & أمبير ؛ ذ نوع الاتصال من وزن الجسم نوع العملية عقارب مواد الجسم ص 11 مادة إسفين f6a + stl المواد الجذعية F6a مادة المقعد f6a + stl كود التصميم api 602 وجها لوجه البعد Asme b16.10 اختبار وفحص api 598 الضغط & أمبير ؛ مؤقت اسمي ب 16.34 متوسط الماء والنفط والغاز الأصل الصين صمام بوابة api602 1 بوصة 0.75 بوصة 900 رطل من وزن الجسم عقارب وزن الجسم

a105n 0.5 بوصة صمام بوابة الترددات اللاسلكية
متكاملة شفة الترباس بونيه a105n صمام بوابة تتحمل كامل

api602 بوابة صمام الترباس بونيه خارج المسمار نير إسفين كامل تتحمل متكامل اتصال رفع شفة الوجه a105n الجسم تقليم 13cr 150lb 300lb 1/2 بوصة 3/4 بوصة a182 f6a مقعد / إسفين / جذع ، 304 + الجرافيت / حشية ونبسب ؛

صمام بوابة 800 رطل dn20
dn20 800lb الصلب مزورة a105 sw bb بوابة عقارب صمام a105

dn20 800lb pn130 الصلب مزورة a105 sw طريقة اتصال نظام التشغيل & amp ؛ y صمام عقارب بوابة تشغيل الهيكل وغطاء المحرك a105 api600 تقليم 8 مقاعد 410 + stl wedge 420 stem 410 طوقا 304 + تصميم الجرافيت وتصنيع api602 وجها لوجه ansi b16.11 أبعاد نهاية ملحومة api 602 الاختبار والتفتيش api 508. تفاصيل سريعة نوع صمام البوابة بحجم dn20 الضغط 800 رطل اعمال بناء ب ، السراج & أمبير ؛ ذ الإتصال sw وضعية التشغيل عقارب مواد الجسم أ 105 التغطية أ 105 تصميم & أمبير ؛ صناعة api 602 نهاية الاتصال api 602 تفتيش api 598 نطاق درجة حرارة -29 ℃ ~ + 425 ℃ متوسط النفط والماء والغاز

1 بوصة 800 رطل بوابة صمام BB OSY SW
1 بوصة 800 رطل بوابة صمام BB OSY SW

تم تصميم صمام البوابة مقاس 1 بوصة 800 رطل وفقًا لواجهة برمجة التطبيقات 602 مع تشغيل sw و handwheel. يحتوي صمام البوابة f316 من الفولاذ المقاوم للصدأ على غطاء محرك مثبت بمسامير ومسمار خارجي ونير.

صمام بوابة تزوير
1 بوصة 600LB تزوير بوابة صمام API 600 عقارب الجذعية

بوابة الصين 1 بوصة, الشركة المصنعة للصمام Dervos توفر صمام بوابة 1 بوصة ، أ 105 ، API 600 ، كلاس600, شفة ، عقارب عملية.

صمام البوابة
صمام بوابة فولاذي مزور 1 بوصة إسفين صلب 300LB

يتكون صمام البوابة الفولاذي المصنوع من الصلب مقاس 1 بوصة من شفة متكاملة , غطاء محرك بمسامير , ساق صاعد وإسفين صلب وغطاء محرك مثبت بمسامير . يحتوي الصمام على معيار التصميم API 602 ومعيار الفحص API 598 . يمكن أن تقدم dervos خدمة التخصيص من خلال تزويد العملاء بصمامات بأحجام مختلفة , المواد , المعايير , ضغط التصميم , الهيكل , نوع العملية ونوع التوصيل .

صمام البوابة
1 "800LB مزورة الصلب بوابة صمام BW * NPT F5 API602

1 "800LB بوابة صمام مصنوع وفقًا لمعيار API 602. جسم الصمام مصنوع من A182-F5. له الخصائص الهيكلية للبوابة الصلبة ، وغطاء المحرك الملحوم وجسم الصمام الممتد 100 مم. وضع الاتصال هو BW * NPT. وهو لديه وضع تشغيل عجلة اليد.

صمام البوابة
DN50 PN40 صمام بوابة فولاذي مزورة A105 عجلة يدوية ISO

تم تصنيع صمام البوابة DN50 PN40 وفقًا لمعيار EN ISO 15761. جسم الصمام مصنوع من ASTM A105N. لها الخصائص الهيكلية للإسفين الصلب ، التجويف الكامل ، الجذع الصاعد والغطاء المثبت بمسامير. وضع الاتصال الخاص به هو EN1092-1 B1. ولها وضع تشغيل عجلة اليد.

صمام البوابة
1/2 "300LB مزورة الصلب بوابة صمام A105N API602 BB OS&Y RF

تم تصنيع صمام البوابة 1/2 "300LB وفقًا لمعيار API602 و ASME B16.34. جسم الصمام مصنوع من A105N. له الخصائص الهيكلية لـ BB ، OS&Y ، إسفين صلب ، NACE MR0175 ، بدل التآكل 3 مم ومستوى التسرب ISO5208A وضع الاتصال الخاص به هو RF بشكل عام ، ولديه وضع تشغيل عجلة اليد.

صمام بوابة غطاء محرك ختم الضغط
ضغط صمام بونيه بوابة صمام وزن الجسم 8 بوصة 2500 رطل

تم تصميم صمام البوابة 2500 فئة 8 بوصات بغطاء مانع للتسرب ، ووصلة لحام بعقب ، وتشغيل علبة التروس. يحتوي صمام البوابة 8 بوصة على جسم WCB من الفولاذ الكربوني وتقليم 5. تفاصيل سريعة نوع بوابة   صمام بحجم 8 " ضغط التصميم ansi   2500 اعمال بناء الضغط   غطاء الختم ، إسفين مرن ، مقعد من المعدن إلى المعدن نوع الاتصال بعقب   اللحام (SW) نوع العملية ناقل الحركة   عملية مواد الجسم أ 217   wc6 مواد تقليم تقليم 5 كود التصميم api 600 وجها لوجه البعد اسمى   ب 16.10 نهاية الاتصال اسمى   ب 16.25 الضغط & أمبير ؛ مؤقت اسمى   ب 16.34 متوسط ماء،   النفط والغاز الأصل الصين البعد & أمبير ؛ مواد nps dn صف دراسي 2 2 1/2 3 4 6 8 10 12 14 16 18 20 24 50 65 80 100 150 200 250 300 350 400 450 500 600 ل (الترددات اللاسلكية) 900 رطل 368 419 381 457 610 737 838 965 1029 1130 & emsp؛ & emsp؛ & emsp؛ 1500 رطل 368 419 470 546 705 832 991 1130 1257 1384 & emsp؛ & emsp؛ & emsp؛ 2500 رطل 451 508 578 673 917 1022 1270 & emsp؛ & emsp؛ & emsp؛ & emsp؛ & emsp؛ & emsp؛ L1 (وزن الجسم) 900 رطل 216 254 305 355 508 660 787 914 991 1092 1346 1473 1600 1500 رطل 216 254 305 406 559 711 864 991 1067 1194 1697 & emsp؛ & emsp؛ 2500 رطل 279 330 368 457 610 762 914 1041 1118 1245 & emsp؛ & emsp؛ & emsp؛ l2 (rtj) 900 رطل 371 422 384 460 613 740 841 968 1038 1140 & emsp؛ & emsp؛ & emsp؛ 1500 رطل 371 422 473 549 711 841 1000 1146 1276 1407 & emsp؛ & emsp؛ & emsp؛ 2500 رطل 454 514 584 683 927 1038 1292 & emsp؛ & emsp؛ & emsp؛ & emsp؛ & emsp؛ & emsp؛ ح (أوبن) 900 رطل 554 637 680 796 1084 1372 1494 1550 1960 2210 & emsp؛ & emsp؛ & emsp؛ 1500 رطل 554 637 767 875 1094 1372 1655 1834 2150 2260 2460 2721 2940 2500 رطل 610 654 753 850 1254 1374 1685 1894 2226 2382 2585 & emsp؛ & emsp؛ ث 900 رطل 300 350 350 400 560 460 * 610 * 610 * 610 * 760 * & emsp؛ & emsp؛ & emsp؛ 1500 رطل 300 450 450 560 305 * 460 * 610 * 610 * 760 * 760 * & emsp؛ & emsp؛ & emsp؛ 2500 رطل 500 500 600 600 460 * 460 * 610 * & emsp؛ & emsp؛ & emsp؛ & emsp؛ & emsp؛ & emsp؛ الوزن (rf) 900 رطل 50 84 92 154 341 622 950 1295 1720 2380 & emsp؛ & emsp؛ & emsp؛ 1500 رطل 60 91 128 182 394 795 1370 2120 2800 3870 & emsp؛ & emsp؛ & emsp؛ 2500 رطل 121 175 195 229 720 1295 2250 & emsp؛ & emsp؛ & emsp؛ & emsp؛ & emsp؛ & emsp؛ الوزن (وزن الجسم) 900 رطل 39 64 82 120 266 524 760 1090 1450 2018 & emsp؛ & emsp؛ & emsp؛ 1500 رطل 46 71 85 130 292 578 974 1615 2010 2815 3315 4150 5219 2500 رطل 88 135 144 158 500 892 1550 1978 2580 3780 5988 & emsp؛ & emsp؛ * يوصى باستخدام مشغل التروس اليدوي لا. جزء WCB wc6 wc9 ج 5 راجع 8 CF 8M 1 الجسم a216 wcb a217 w6 a217 wc9 a217 c5 a351 cf8 a351 cf8m 2 مقعد a182 f6a a182 f22 a182 f22 a182 f5 a182 f304 a182 f316 3 وتد a216 wcb a217 w6 a217 wc9 a217 c5 a351 cf8 a351 cf8m 4 إيقاف a182 f6a saehnv3 a182 f304 a182 f316 5 مربع حشو a216 wcb a217 w6 a217 wc9 a217 c5 a351 cf8 a351 cf8m 6 ختم Ansi 316l الجرافيت المرن + 316 7 حلقة الانقسام صلب و ٦ و ٦ و ٦ a182 f304 ص 316 8 الحلقة الخلفية صلب صلب صلب صلب SS SS 9 الترباس أ 193 ب 7 أ 193 ب 7 أ 193 ب 7 أ 193 ب 7 أ 193 ب 8 أ 193 ب 8 10 البندق أ 194 2 ساعة أ 194 2 ساعة أ 194 2 ساعة أ 194 2 ساعة أ 194 غرام 8 أ 194 غرام 8 11 نير a216 wcb a217 w6 a217 wc9 a217 c5 a351 cf8 a351 cf8m 12 الترباس أ 193 ب 7 أ 193 ب 7 أ 193 ب 7 أ 193 ب 7 أ 193 ب 8 أ 193 ب 8 13 البندق أ 194 2 ساعة أ 194 2 ساعة أ 194 2 ساعة أ 194 2 ساعة أ 194 غرام 8 أ 194 غرام 8 14 لوحة التعبئة أنسي 410 أنسي 410 أنسي 410 أنسي 410 انسي 304 انسي 316 15 التعبئة الجرافيت مرنة (مضفر   وخاتم) أو ptfe 16 انقسام دبوس صلب صلب صلب صلب صلب صلب 17 ييبولت أ 193 ب 7 أ 193 ب 7 أ 193 ب 7 أ 193 ب 7 أ 193 ب 8 أ 193 ب 8 18 السدادة a182 f6 a182 f6 a182 f6 a182 f6 a182 f304 a182 f316 19 شفة الغدة أ 105 أ 105 أ 105 أ 105 a182 f304 a182 f316 20 البندق أ 194 2 ساعة أ 194 2 ساعة أ 194 2 ساعة أ 194 2 ساعة أ 194 غرام 8 أ 194 غرام 8 21 عشيق أ 193 ب 7 أ 193 ب 7 أ 193 ب 7 أ 193 ب

 الصلب مزورة a105 صمام الكرة npt
dn25 pn100 مزورة الصلب الكرة npt a105 صمام

dn25 pn100 مزورة الصلب a105 طريقة اتصال npt 2 قطعة البناء كامل المسام رافعة عملية العائمة الكرة سلامة الجسم النار وغطاء المحرك a105 الكرة a182 f304 حلقة مقعد ptfe الجذعية a182 f304 الجذعية o ring viton التعبئة الجرافيت الغدة الفولاذ المقاوم للصدأ تصميم وتصنيع asme b16.34 وجها ل وجه تصميم تصنيع قياسي تصنيع برغي وأبعاد قياسية ansi b1.20.1 فحص واختبار api598 تصميم السلامة من الحرائق api 607 تفاصيل سريعة نوع صمام الكرة بحجم dn25 الضغط pn100 اعمال بناء 2 قطعة الإتصال npt وضعية التشغيل رافعة مواد الجسم أ 105 التغطية أ 105 تصميم & أمبير ؛ صناعة اسمي ب 16.34 من النهاية إلى النهاية Asme b16.10 نهاية الاتصال ansi b1.20.1 تفتيش api 598 نطاق درجة حرارة -29 ℃ ~ + 538 ℃ متوسط النفط والماء والغاز

اترك رسالة

    إذا كنت مهتما في منتجاتنا و تريد أن تعرف المزيد من التفاصيل,يرجى ترك رسالة هنا وسوف نقوم بالرد عليك بأسرع ما يمكن.

الصفحة الرئيسية

منتجات

حول

اتصل